Panbio™ COVID-19/Flu A&B Panel Self Test

Place of Origin

South Korea

Benefit

Panbio™ COVID-19/Flu A&B Panel Self Test allows patients to test for COVID-19/ Flu A and/or B infection in the comfort of home. The test is over 90% accurate, uses single patient-friendly nasal swab and offers fast results in 15 minutes. Test Now. Be Sure.

Product Usage

BEFORE STARTING: Wash or sanitize your hands.
Make sure they are dry before
starting.
A. PREPARE FOR THE TEST: Check the expiration date on the box. Do not use if the kit is
expired.
12. Keep test device flat on a surface.
Start timer. Read result at 15 minutes.
Do not read the result earlier than 15
minutes or after 20 minutes.
7. Remove buffer tube from
tube rack and insert the swab
into the buffer tube.
Swirl the swab in the fluid 5
or more times while pushing
against the wall of the buffer
tube.
Squeeze the buffer tube
around the swab tip to remove
any remaining fluid.
8. Hold the buffer tube firmly
with one hand. Lift the swab
inside the tube and locate
the break line.
Snap the swab handle at the
break line.
Leave the swab in the tube
and discard the stick.
Press the nozzle cap tightly
onto the buffer tube.
5. Swab both nostrils.
Insert the soft end of the
swab straight back into your
nostril until resistance is felt
(about 2 cm).
Slowly rotate the swab, gently
rubbing it along the insides of
your nasal passage at least 5
times.
Remove swab from nostril.
6. Using the same swab, repeat
step 5 in your other nostril.
2 cm
Rotate at least 5x
in each nostril
9. Return the buffer tube to the
tube rack before proceeding
to the next step.
4. Open swab protective
package at stick end.
Take swab out.
11. Squeeze 4 drops of
liquid from the buffer
tube into the well on
the test device.
Close the nozzle using
cap.
Place the buffer tube
into the waste bag and
wait 15 minutes.
4 drops
3. Keep buffer tube upright and
remove foil. Place the buffer
tube in the tube rack before
proceeding to the next step.
3: OPEN BOTTLE
squeeze
14. Seal the waste
bag tightly.
18: SEAL BAG
15. Place the waste
bag into waste
19: DISbiPnO. SE
6: OPEN SWAB
13. Place the test
device into the
waste bag.
If Control line (C) is present, no matter how
faint, and no result lines are present the test is
showing a NEGATIVE result.
This means, COVID-19, Influenza A and
Influenza B were not detected.
17: PLACE COMPONENTS INTO BAG
10. Remove the test device
from its protective package
and place on a well-lit, flat
surface.
12: TEST
click!
2. Ensure kit is at room temperature for at least 30 minutes prior to
use.
Open the kit box and remove one of each of the components
shown below to perform a single test.
Do not open individual components until instructed.
Find the result window.
! C indicates control line.
If no control line (C) is present, the
test did not work and is considered
INVALID.
This may be as a result of an incorrect
test procedure and the test should be
repeated. Wait 4 hours before repeating
the test using a new nasal swab sample.
WAIT 15 MINUTES
15 READ AT 15-20 MINUTES min
1 test device 1 buffer tube 1 nozzle cap 1 swab
1 tube rack
1 waste

Ingredients

NA

Shipping Information

2°C - 30°C

Pieces per Container

1 Test

Storage Condition

2°C - 30°C

Skin Type

Others

Warnings

Do not store the test kit in direct sunlight.
3. Keep the test out of reach of children and pets.
4. Read instructions prior to performing the test. Follow all instructions to achieve accurate results.
5. Individuals below 16 years of age and persons with reduced physical

Width

5.5

Height

2.5

Depth

12